Addonics Technologies Network Card WDAUSM User Manual

T E C H N O L O G I E S  
User Guide  
WiFi Drive Adapter  
(WDAUSM, WDAUSM-P)  
Technical Support  
If you need any assistance to get your unit functioning properly, please have  
your product information ready and contact Addonics Technical Support at:  
Hours: 8:30 am - 6:00 pm PST  
Phone: 408-453-6212  
 
Network Cable  
USB Power cable  
(Included with Model WDAUSM, WDAUSM-P)  
Power Supply  
(Included with Model WDAUSM-P)  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
Initial Setup  
Initial Setup  
1. Prepare storage.  
- Choose a MicroSD card or USB storage.  
- Make sure the storage device is formatted with one partition, FAT32  
or FAT64 (exFAT).  
NOTE: FAT32 may be used for storage capacity up to 2TB. FAT64 may be used for storage  
capacity up to 4TB. USB hard disks with large sector size will not be compatible. Most retail USB  
hard disks larger than 2TB will have the large sector size.  
2. Connect one storage to the WiFi Drive Adapter.  
- The WiFi Drive Adapter only supports one storage device at a time.  
- If a MicroSD and USB storage are attached, only the MicroSD will  
work.  
- The unit will not support multiple USB storage devices or hubs.  
- If a USB storage device with independent power is connected, use  
the storage device's power supply to power it.  
3. Connect the unit to a router using the provided ethernet cable if desired.  
4. Connect power to the unit.  
5. Use a wireless device with a web browser to connect to the WiFi Drive  
Adapter.  
- Use the Wireless settings on the device to locate the network.  
- The WiFi Drive Adapter's default Wireless network name will be  
“Addonics_WDA” followed by some numbers.  
- The default wireless password is “12345678”  
- This step may be skipped if the unit is connected to a router using  
ethernet.  
The following steps are optional if customization is desired:  
6. Open a web browser and connect to the WiFi Drive Adapter's Web  
Interface.  
- If connected using wireless, type 192.168.99.1 into the address bar  
and press Enter.  
- If connected using ethernet, refer to your router's DHCP Clients  
table to discover the WiFi Adapter's IP address. The unit's default  
hostname will be “Addonics_WDA” followed by some numbers.  
Type that IP address into the address bar on the web browser  
(instead of 192.168.99.1) and press Enter.  
- The web interface will ask for a username and password. Type  
“admin” into both (without the qoutes).  
7. Change the device name if desired.  
- This will be the unit's Wireless Network name, as well as its  
Windows Network name.  
- This setting is found in the “System Setting” menu.  
8. Change the Web Interface password if desired (recommended):  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
- the default password is “admin”  
- the setting is “Admin Password” in the “System Setting” menu.  
- This setting only affects the Web Interface.  
9. Change the Date and Time if desired (recommended):  
- The setting is “Date & Time” in the “System Setting” menu.  
- Change the Time Zone before setting the date and time.  
- “Sync from internet” is enabled by default.  
Locating the WiFi Drive Adapter on the network  
Always refer to the WiFi Drive Adapter using its IP address. If connecting to  
the unit using wireless networking, the unit's IP address is 192.168.99.1. If  
connecting to the unit using a router it is attached to using ethernet, refer to  
the router's DHCP clients table, or use the static IP address configured in the  
web interface if the unit was configured for Static IP.  
Using the WebDAV Interface  
To access the WiFi Drive Adapter's storage using a web browser, connect to  
the WiFi Drive Adapter's web interface, then click the WebShare menu. From  
there, click “disk1.” The attached storage device's entire contents will be  
shown on the next page.  
To open a folder on the storage device, simply click on it.  
To download a file, click on the filename, or to save it to local storage  
right-click (or on Mac systems, Control-click) the filename then choose your  
browser's “Save As” menu option (such as “Save target as...”).  
Clicking the Options button on the top of any page opens a small menu,  
where a folder can be created (“Create Folder”), or return to the Web  
Interface main menu (“Go Home”).  
Clicking the option button on a file or folder's line opens a small menu where  
that item may be renamed or deleted.  
Using the SMB Server:  
On Windows:  
Open a Windows Explorer window, then type two backslashes “\\” followed  
by the WiFi drive adapter's IP address (see “Locating the WiFi Drive Adapter  
on the network”). Then press Enter. Next, open the share “disk1.” The  
attached storage will then be available with full permissions.  
On MacOS:  
From the Finder menu, choose “Go” then pick “Connect to Server...” In the  
Server Address box, type “smb://” followed by the WiFi Drive Adapter's IP  
address (see “Locating the WiFi Drive Adapter on the network”). Then press  
Enter. Next, open the share “disk1.” The attached storage will then be  
available with full permissions.  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
The WiFi Drive Adapter Menus  
System Setting Menu  
Device Name: this option changes the WiFi Drive Adapter's Wireless  
Network Name, and also its hostname.  
Admin Password: this option changes the password used for accessing the  
Web Interface.  
Date&Time: this option is used to change the WiFi Drive Adapter's date and  
time settings. Choose the time zone first, then check “Sync from internet” to  
access time from an Internet connection. If manual settings are desired,  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
un-check “Sync from internet,” then either change the date and time fields to  
the settings desired, or click “Sync from your device” to set the time based on  
the computer or device you are using to change the settings.  
Power Saving: The WiFi Drive Adapter includes a sleep mode, which places  
the unit and storage into low power mode. This can be set to None, leaving  
the unit active at all times, or a selection of 5 minutes, 10 minutes, or 30  
minutes.  
Reboot: this causes the WiFi Drive Adapter to restart.  
Shutdown: this option sets the unit immediately into low power mode.  
Wireless Network Menu  
Security: this option may be used to enable or disable WPA2 password  
protection for the WiFi Drive Adapter's wireless network, and if enabled, the  
password may be changed here. The default password is “12345678.”  
Internet Access: this option may be used to enable or disable using the WiFi  
Drive Adapter with a wireless Router to connect to the Internet. When  
enabled, a list of available wireless networks is shown. Only networks with no  
authentication or WPA2 authentication with 8 or 13 character passwords are  
supported. This option has no effect if the WiFi Drive Adapter is connected to  
a router using an ethernet cable.  
WiFi Channel: this option is used to select the WiFi Drive Adapter's wireless  
network channel. This setting applies to the unit's wireless network, not the  
Internet Access wireless network connection.  
WAN Setting Menu  
This menu is used to configure the WiFi Drive Adapter's ethernet connection  
to a router. By default, the unit will connect using DHCP, and acquire settings  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
from the router. This may be changed to “Static” for manually setting an IP  
address, network mask, gateway, and one or two DNS Servers.  
Utility Menu  
Disk format: this option may be used to format the attached storage device.  
NOTE: While the WiFi Drive Adapter supports storage devices up to 4TB in  
capacity, this option may only be used to format storage devices up to 2TB in  
capacity.  
Firmware Upgrade: this option is used to update the WiFi Drive Adapter's  
internal operating system firmware. Details on how to perform this upgrade  
will be described in the firmware upgrade release notes.  
Factory Default: this option is used to reset the unit to the original settings,  
losing all custom settings. The wireless networking and hostname will revert  
to “Addonics_WDA” followed by some numbers, the wireless network  
password will revert to “12345678,” the Web Interface password will revert to  
“admin” and the WAN settings will revert to DHCP.  
UI Setting Menu  
Language: this option is used to select the language used by the Web  
Interface.  
Theme: this option is used to select one of several choices for the colors  
used in the Web Interface.  
WebShare Menu  
This menu is used to access the WebDAV server. See “Using the WebDAV  
Interface.”  
CONTACT US  
Phone:  
Fax:  
Email:  
408-573-8580  
408-573-8588  
 

Acer Laptop 2930 User Manual
Acer Projector X1160Z User Manual
ADC Network Card FL2000 Series User Manual
ADTRAN Network Card TR NWT 000829 User Manual
Aiphone Home Security System 261380 User Manual
Aiphone Stereo Amplifier LAH 20 User Manual
Air King Ventilation Hood AIF10X User Manual
Airlink101 Computer Drive AEN U35 User Manual
Aviva Sports Baby Toy 11000 User Manual
BC Speakers Speaker 10PLB76 User Manual