Addonics Technologies Network Card CRTM4HES User Manual

ADDONICS TECHNOLOGIES  
Model: CRTM4HES  
II. Connecting the power cable and Cipher Tower to the  
IMPORTANT  
computer  
There is no back door for the Cipher tower encrypted hard  
drives if the Cipher keys are lost or stolen.  
a. Connect the power cord provided from the wall outlet to the  
back of the Cipher Tower.  
b. A power switch is located on the front of the tower. Make  
sure the power is off on the switch (power LED light should  
be off)  
Cipher key  
Check to make sure you have the  
correct version of the Cipher key. A  
sample key is shown  
c. Connect the provided eSATA cable from the back of the  
Cipher tower to the eSATA port on the computer.  
Black label AES-256 stands for  
Cipher 256-bit key.  
To ensure there is a spare key, your Cipher tower comes with  
4 pairs of Cipher keys. These cipher keys have all identical  
encryption code unless you requested then to be coded  
differently. One of these keys should be kept in a safe and  
secure location and can be sent back to Addonics for duplicating  
additional keys. If you are down to the last key, be sure to make  
a back up of all the data stored inside your Cipher tower prior to  
sending the last key to Addonics. Addonics is not responsible for  
key lost in the mail or retrieval of the data inside the encrypted  
hard drive.  
Power  
Switch  
Keeping track of the hard drive  
(LED 4)  
HPM  
Health  
(LED 2)  
USB  
Status  
Power  
LED  
If you are using the Cipher tower to encrypt multiple hard drives,  
it is important to label your hard drive if you are taking the drive  
out of the Cipher tower. The hard drive from the Cipher tower  
that is encrypted will look like a brand new drive when attach  
directly to the SATA controller of a computer. There will be no  
partition or any hint to indicate that the drive contains encrypted  
data. When the drive is partitioned, all the encrypted data will be  
lost.  
RAID config  
rotary switch  
eSATA port  
(LED 3)  
HPM  
Power  
(LED 1)  
eSATA  
Status  
Cipher  
power  
LED  
RAID  
setting  
button  
Cipher  
keyhole  
The same holds true if a hard drive already has data on it is  
installed into the Cipher tower. The computer detects the hard  
drive as a brand new drive or a drive that is unallocated. Once  
you proceed to partition the drive, the data that was on the hard  
drive will be erased and cannot be recovered.  
LED Information:  
Power LED:  
When power switch is turned on, the green  
LED lights up.  
When the RAID volume fails, the LED  
I. Installing drives into the Cipher Tower  
HPM Health LED:  
blinks.  
eSATA status LED: When eSATA port is used to connect to a  
system, the LED lights up.  
When USB port is used to connect to a  
system, the LED lights up.  
Open the front panel of the Cipher  
tower.  
USB status LED:  
Slide the 3.5” SATA hard drive into  
the drive bay.  
Note: It is recommended to fill up the tower with SATA drives  
from top to bottom. This is to help in identifying which drives  
connect to which ports for easier troubleshooting.  
 

3Com Network Card 3CR990 FX 97 User Manual
ADTRAN Two Way Radio ISU 2X64 User Manual
AEG Cooktop HK854220IB User Manual
Agilent Technologies Switch U2751A User Manual
Airstream Automobile 396 User Manual
Alloy Computer Products Network Card BWS 136 User Manual
Amana Clothes Dryer W10562495A User Manual
Atmel Computer Hardware AT91CAP7A STK User Manual
Audiovox Stereo Amplifier AMP 602 User Manual
Baratza Coffee Grinder Virtuoso User Manual