Addonics Technologies Network Card ADSA4R E User Manual

Addonics Technologies, Inc.  
ADSA4R-E (4-Port External SATA PCI Controller Card)  
SPECIFICATIONS  
INSTALLATIONS  
Chip Set: Silicon Image Sil3114 integrated host  
Controller  
Hardware Installations:  
Interface: PCI bus compatible  
I/O Ports: (4) eSATA Connectors  
Regulatory approvals: FCC, CE  
Features:  
1. Power OFF PC and remove its cover.  
2. Select an empty PCI slot and insert the SATA  
Controller.  
3. Makes sure to secure the bracket with a screw.  
4. Close the PC’s cover.  
5. Turn PC ON.  
·
·
Up to 150 Mbytes/sec (1.5 Gbits/sec) per port  
4 External SATA (eSATA) ports with the new SATA  
External connector  
Software Installation:  
·
·
·
Work with any SATA drive  
Use as a non-RAID or RAID controller  
Built-in RAID 0, RAID 1, RAID 1+0, RAID 1+ S  
support  
Support large hard drives of 137 GB or greater  
Upgradeable firmware  
Windows NT4.0, 2000, XP, 2003 Driver Installations  
1. Turn computer ON. When Windows boots up, “A  
New Hardware Found” pops on the screen and the  
Addonics Serial ATA PCI Host Controller is  
identified.  
2. At the “Add New Hardware Wizard Window, click  
“Next”  
·
·
·
·
Hot-plug capability  
Fits standard height Desktop case  
3. Choose “Select for the best driver for your devices”,  
and click “Next”  
4. Insert the Drivers Diskette and check the “Floppy  
Drive” option. Click “Next”  
5. If using a driver that has not been digitally signed by  
Microsoft, you will be asked if you want to continue  
the installation. Click Continue.  
6. When the new hardware wizard has finish installing  
the Serial ATA card. Click “Finish” to complete the  
installations.  
Confirming Serial ATA Driver Installation  
1. Right click the My Computer icon and select  
properties.  
2. Click Device Manager in the Menu Tree.  
3. Click the “+” sign in front of SCSI controllers. Silicon  
Image SATA controller should appear.  
Important Note:  
System Requirements:  
·
·
·
To do a RAID SET, you can press F4 or CTRL+S  
from the boot up screen. Read and follow the  
instruction inside the BIOS screen.  
You can also install the SATA GUI utility Under  
Windows to monitor the RAID Set. It is under the  
Utility section of the driver disc.  
·
·
Computer with one available PCI slot  
Windows DOS/NT/2000/XP/2003 server  
RAID 0/1 described  
Stripe (RAID 0): Greatly increases the performance of data  
transfer by simultaneously writing data to 2 drives.  
Mirror (RAID 1): duplicates or mirrors the data on both  
drives. No data will be lost if one of the drives fails.  
Mirror-Striping (RAID 0+1) Combined both Striping and  
Mirroring technologies to provide both the performance  
enhancements that come from Striping and the data  
availability and integrity that come from Mirroring.  
RAID 1+S (Mirrored-Sparing) Can automatically replace the  
failed drive and rebuild the system when booting HDD failed.  
Use the controller BIOS setup for creating RAID  
SET.  
SUPPORT  
Main: Addonics Technologies  
2466 Kruse Drive  
San Jose CA 95131  
Phone: 408 433-3899  
Fax: 408 433-3898  
Technical Support (8:30 am to 5:30 pm PST)  
Phone: 408 433-3855  
Note: Specifications subject to change without notice.  
Copyright © 1998 - 2005 Addonics Technologies, Inc. All Rights Reserved.  
 

2nd Ave Gas Grill 0023W934 User Manual
ADC Clothes Dryer AD 30V User Manual
AeroGarden Greenhouse Kit 300291 User Manual
Agilent Technologies Webcam 89600 User Manual
Allied Telesis Switch Rapier Switch User Manual
Allstar Products Group Garage Door Opener 110927 User Manual
Alpine Cooktop PXA H701 User Manual
AOC TV Video Accessories I2778VHE6 User Manual
Avet Reels Fishing Equipment LX 80 User Manual
Behringer Car Speaker B215XL B215XL WH User Manual