Addonics Technologies Computer Hardware RT5835HMEU User Manual

ADDONICS TECHNOLOGIES  
Model: RT5835HMEU  
I.  
Installing drive into the RAID Tower V  
Step 1  
Set A (4-drive HPM)  
Use a Philips screwdriver to secure the 3.5”  
SATA hard drive to the drive tray  
Step 2  
Slide the tray into the Disk Array drive bay.  
Note: It is recommended to fill up the RAID  
Tower V with SATA drives from right to left  
and top to bottom. This is to help in identifying  
which drives connect to which ports for easier  
Set B  
(4-drive HPM)  
troubleshooting.  
II. Connecting the power cable and RAID Tower V to the  
computer  
a. Connect the power cord provided from the wall outlet to the back of  
the RAID Tower.  
b. Make sure the power is off (power LED light should be off).  
Set A (4-drive HPM)  
Set B (4-drive HPM)  
c. Connect either the provided USB or eSATA cable from the back of  
the RAID Tower to the computer. We recommend connecting the  
eSATA port for best performance if this port is available on your  
computer.  
Photo identifying SATA port s on HPM  
LED pins  
SATA  
RAID  
setting  
button  
Port 3  
SATA  
Port 1  
USB port  
Pin 1  
RAID config  
rotary switch  
SATA  
SATA  
Port 2  
Port 4  
eSATA port  
Power Switch  
Power Connector  
III. Power on/off control  
Turn on the power to the RAID Tower Mini by pressing the power  
button on the front. The power LED light should lit indicating the power  
is on.  
IV. Setting RAID on the HPM  
1. Attach the SATA hard drives (up to 4) to the SATA ports on the  
Hardware Port Multiplier (HPM) using SATA cables. It is  
recommended to connect drives to the SATA ports 1 to 4  
successively.  
2. Set the Rotary switch to the RAID mode required.  
3. Push the RAID setting button with a ballpoint pen tip while the HPM  
is turned off.  
Power LED  
Power Switch  
HPM 1 (Top disk array)  
(LED 1) HPM Health  
Use a ballpoint pen  
tip to press the  
RAID Setting Button  
(LED 2) eSATA Status  
(LED 3) USB Status  
4. While holding the RAID setting button, turn on the HPM and SATA  
hard drives and continue to hold button for at least 5 seconds.  
HPM 2 (Bottom disk array)  
(LED 1) HPM Health  
(LED 2) eSATA Status  
(LED 3) USB Status  
Note:  
The onboard LED's for the eSATA and USB will start blinking  
while holding down the raid setting button. Once the raid  
setting button is released, the PM Health LED will blink 4-6  
times.  
If the PM Health LED stops blinking, the raid set is set  
correctly. If the PM Health LED lights up as solid green, it is a  
bad setup. You need to repeat setting up the raid again.  
 

3Com Network Card 10 100BASE T4 PCI User Manual
3M Home Theater System X21i X26i X30n X31 X31i X35n X36 X36i User Manual
ADC Power Supply Power Distribution Products User Manual
Advantech Laptop IPPC 9120 User Manual
AEG Refrigerator 80318 5 KG User Manual
Amana Refrigerator Compact Refrigerator Freezer User Manual
American Standard Hot Tub 6060E SERIES User Manual
ATI Technologies DVD Player HD 3450 User Manual
BB Electronics Network Card 232PCC2 User Manual
Beko Oven OIM22500P User Manual