Addonics Technologies Computer Drive AEIDDSAU User Manual

ADDONICS TECHNOLOGIES  
Model: AEIDDSAU, AEIDDSAUWP (read only mode)  
The internal SATA / USB DigiDrive supports Type I, II  
Close mode – force flash media to become  
Removable disk type  
CF Cards, CF Micro drive, SD, SDHC, miniSD (with  
adapter), Trans flash, SD HS (Secure Digital High  
Speed), MMC Cards (4-bit and 8-bit modes), RS-  
MMC, MMC-Micro, MMC Plus, Smart Media, xD  
picture card- both H and M types, Memory stick,  
Memory stick PRO, MS Extreme III Type media, MS  
PRO, HS (4-bit mode).  
Drive icon  
Media Detection  
Hot Swap  
NOT RECOMMENDED  
SATA port  
Non hot swap  
SATA port  
Icon always there  
with or without flash  
media inside the  
DigiDrive  
Flash media  
automatically  
detected when  
added or remove  
II.  
Setting up the device in USB Mode  
a. Connect a 4-pin floppy power cable to the internal  
SATA / USB DigiDrive.  
b. Attach USB 5-pin header from internal SATA /  
USB DigiDrive to USB header on PC.  
c. The drive icon appears only when flash media is  
inside the internal SATA / USB DigiDrive.The drive  
icon will disappear and reappear during media  
change.  
Note for AEIDDSAUWP: If an unformatted flash media  
is use, no drive icon will show up in My Computer.  
Mode jumper JP4  
(close or open)  
Media Priority  
USB 5-pin  
header  
When more than one media is inside the internal  
SATA / USB DigiDrive during bootup, the media that  
gets detected first is according to the priority shown  
below  
Pin 1  
4-pin floppy  
power connector  
1. Compact Flash  
SATA port  
2. Smart Media / xD Picture card  
3. MMC / SD  
4. Memory Stick  
Mode Jumper (JP4):  
Note: Only applies on SATA connection  
I.  
Setting up the device in SATA mode  
a. Connect a 4-pin floppy power cable from PC to the  
internal SATA / USB DigiDrive.  
b. Attach SATA cable from internal SATA / USB  
DigiDrive to the PC SATA port.  
The tables show drive icon and media detection  
behavior basing on the mode switch setting and the  
type of SATA port the internal SATA / USB DigiDrive is  
connected to.  
Open mode – force flash media to become Fixed disk  
type  
Drive icon  
Media Detection  
Flash media is  
automatically  
Hot Swap  
SATA port  
Icon appears only  
when flash media is  
inside  
TECHNICAL SUPPORT  
refresh and  
detected when  
added or removed  
Flash media  
detection requires  
manual refresh in  
Device Manager  
Email:  
Internet:  
Non hot swap  
SATA port  
Icon appears only  
when flash media is  
inside  
Technical Support (8:30 am to 6:00 pm PST)  
Phone:  
Email:  
408 453-6212  
 

3Com Switch 5104M FIB User Manual
AC International Styling Iron AC2CIG User Manual
AEG Ventilation Hood CHDF 6260 User Manual
Air King Fan 6C507B 9145B User Manual
Aiwa Car Stereo System ADC M55YU User Manual
AO Smith Water Heater BFC 30 User Manual
Athena Technologies Portable Speaker 5 User Manual
Audiovox Satellite Radio XMCK 5P User Manual
Barco Camera Lens R9840900 User Manual
Behringer Music Mixer BCN44 User Manual